If I had two separate devices I would simply configure subinterfaces on a a router port and proceed with router-on-a-stick configuration.
Router on a stick vlan how to#
HOW TO CONFIGURE ROUTER ON A STICK We are going to configure the router on a stick according to the below-given diagram. I understand my problem comes from the fact that the 878 has inside both a router and a switch, and the ports connecting the two are "hidden". The router on a stick is the virtual LAN configuration which allows you to add multiple VLAN to the single port of the router. What I want is to connect the trunk port on my switch to one of the LAN ports on the 878 and be able to route between the 2 segments. This is in reference to the single router terminating the traffic from each VLAN. We have discussed the basic logic of VLANs in the previous articles.As you know each VLAN is a seperate VLAN.Each of them is a single network. Many companies use to divide their networks into different departments. VLANs are the virtual LANS that provide divide your big network, into smaller pieces. R1(config-subif)encapsulation dot1Q 3 ng gi giao thc dot1.q cho VLAN 3 R1(config-subif)ip address 192.168.3.1 255.255.255. The Sub-interface feature is sometimes referred to as Router on a Stick or One-armed Router. Router on Stick Configuration on Packet Tracer. Now, in my switch I have configured a port as trunk. Keep in mind, however, that the drawback with all VLANs terminating on a single Router interface is an increased risk of congestion on the link. It does support VLANs and configuration of the switch ports. It supports routing between the (predetermined) WAN port and the 4 LAN ports, which essentially are switch ports and not router ports. The 878 is a beefed-up cousin of the consumer-grade routers ISP distribute for free. VLAN ID: 20, VLAN Name: OPT1 (Wifi-AP), Port 1 Tagged, Port 3 Untagged, Not Member 2, 4-8 6.) Navigate to 802.1Q PVID Setting (and set the following by typing the PVID (10,99,20) and selecting the corresponding ports. The thing is the only equipment I have available is a CISCO 878 router that, unfortunately, is a bit peculiar. 11.5.9 Router-on-a-stick Intervlan Routing.
I have tried multiple times to configure the Router on a stick, redoing the sub interfaces and trunking the ports between the equipment, but nothing works.I have 2 distinct network segments (192.168.10.0/24 & 192.168.1.0/24) in my company, and we need them bridged. (I cannot remove the switch that's between the router and the other switch due to other PCs going to be connected in the future) Router>enable Routerconfigure terminal Enter configuration commands, one per line.
Try to assign an IP address to the router and enable the interface you want to configure inter-VLAN routing. I have a setup with 2 - layer 2 switches and a router that has defined sub-interfaces, and for the life of me, I cannot find the error that is stopping the pinging between the PCs. Just need Inter-VLAN Routing which you simply configure according to below step by step Inter-VLAN routing guide. Due to the uneccessary and additional complication of having to resort to using a specific configuration utility with the GS108Ev2 product featured in this guide, I would advise readers look for the updated v3 product which provides a web-based management interface. TL:DR - VLAN 50 cant ping VLAN 80, routing on a stick doesn't. pfSense router-on-a-stick VLAN configuration with a Netgear GS108E Last revised 28 February 2018.
I have a setup which requires two different VLANs to be able to ping one another. (I cannot remove the switch that's between the router and the other switch due to other PCs going to be connected in the future) I have tried multiple times to configure the Router on a stick, redoing the sub interfaces and trunking the ports between the equipment, but nothing works.